What Does R6 Zoning Mean?

R6 zoning is a residential district that usually allows more homes than the zones numbered below it, but how many depends on the city. In New York City, Louisville and Detroit it is apartment zoning, in Nashville it means houses and duplexes on 6,000 square foot lots, and in unincorporated King County, Washington it means a base of six homes per acre. The "R" stands for residential, and the 6 is either a step on the local density ladder, a lot size in thousands of square feet, or a number of homes per acre.

"R6", "R-6" and "R 6" are the same district written three ways. The meaning comes from the local code, not the spelling.

What does R6 zoning mean?

R6 zoning means a residential district that is sixth in a code's list of residential zones, or one named after a number six rule. In codes that count up from single family R1, R6 is normally where apartment buildings become the main use.

That counting pattern is common in residential zoning, but the 6 can mean other things too:

  • A step on the ladder. New York, Louisville and Detroit use R6 for multi-family housing.
  • A lot size. Nashville's R6 requires a lot of at least 6,000 square feet.
  • A density. King County's R-6 is named for six dwelling units per acre, and Raleigh's R-6 was once capped at six units per acre.

So an R-6 lot can hold anything from a single house to a large apartment building. You need the local code to know which.

What R6 zoning means in different cities

R6 is used by big cities and counties alike, and the rules behind the name vary a lot. Each row below comes from the jurisdiction's own zoning code or planning documents:

PlaceDistrict nameWhat it allows (short)
New York City, NYR6 General Residence DistrictApartment buildings. New buildings usually follow height limits, and plain R6 also offers an optional sky exposure plane envelope for taller buildings set back from the street.
Louisville, KYR-6 Residential Multi-FamilyApartments, two-family and single family homes, and assisted living. Up to 17.42 homes per acre.
Detroit, MIR6 High Density ResidentialHigh density multiple dwellings near downtown, New Center and other busy areas. Single family and two-family homes only as conditional uses.
Nashville, TNR6 One and Two-Family ResidentialSingle family homes and duplexes on lots of at least 6,000 sq ft.
King County, WA (unincorporated)R-6 Residential, six DU per acreHomes at a base density of six per acre, with more possible through county density incentives.
Raleigh, NCR-6 Residential-6Detached houses, attached houses and townhouses. Its old cap of six homes per acre was replaced by lot area rules.

Three patterns show up. New York, Louisville and Detroit treat R6 as apartment zoning. Detroit goes furthest: single family houses there are not allowed by right in R6 at all.

Nashville and Raleigh use R-6 for neighborhoods of houses, duplexes and townhouses. Nashville's 6 is the lot size in thousands of square feet, and Metro planning staff reports describe R6 at 7.71 homes per acre, assuming a quarter of the lots hold duplexes.

King County's 6 is simply homes per acre, the same idea as its R-4 and R-8 zones. That zone applies only outside city limits, because each city in King County writes its own zoning.

So what does R6 usually mean? In big-city codes it most often means apartments. In codes that name zones by lot size or density, it means a fairly compact neighborhood of houses, duplexes or townhouses.

How New York City uses R6

New York uses R6 as the first step above its lower density R1 to R5 districts. The city's Zoning Resolution lists R6 among the general residence districts, which allow all types of residential buildings.

A plain R6 lot can be built under two sets of rules:

  • The standard height and setback rules, which cap building height and produce mid-rise buildings closer to the street.
  • Optional sky exposure plane rules, which grew out of the city's older height factor rules. They allow a taller building with no fixed height limit, as long as it is set back from the street and stays under a sloping sky exposure plane.

The sky exposure plane option is not available in R6-1, R6-2 or the lettered districts. The contextual versions, R6A, R6B and R6D, use fixed height limits so new buildings match the existing street. New York rewrote many of its residence district rules in 2024, so older fact sheets with floor area numbers may be out of date. Check the current Zoning Resolution for a specific lot.

Other cities do not copy this system. An R-6 lot in Nashville or Raleigh has nothing to do with New York's height limits or sky exposure planes.

What can you build on R6 zoning?

In most codes R6 allows apartment buildings or, at the low end, a mix of houses, duplexes and townhouses. What fits depends on which kind of R6 the lot has.

Where R6 is a multi-family zone, common projects include:

  • Apartment buildings and condominiums
  • Two-family homes and townhouses
  • Senior housing and assisted living, which Louisville lists in R-6
  • Schools, churches and other community uses, often with a permit

An owner thinking about a multi-family property should check the density cap, height limit, setbacks and parking rules together. The lot coverage calculator helps you test the building footprint before you talk to an architect.

Where R6 is a one and two-family zone, as in Nashville, the main options are a single house or a duplex. Nashville allows the second unit only when the lot meets the minimum size and the code's conditions.

What is the difference between R5 and R6 zoning?

Where a code has both, R6 allows more homes per acre than R5, and the change can mean moving from houses to apartments. Many codes skip one of the two numbers, so a direct comparison only works in some places.

PlaceR5R6
Louisville, KYR-5 Residential Single Family, up to 7.26 homes per acreR-6 Residential Multi-Family, up to 17.42 homes per acre
New York City, NYLower density general residence district with a height capFirst district above the lower density group, with apartment buildings the norm
King County, WANo R-5 zone (the ladder goes R-4, R-6, R-8)Base of six homes per acre
Los Angeles and PhoenixTop multi-family districtNo R6 zone

Louisville shows the biggest jump: R-5 is single family, while R-6 more than doubles the allowed density and adds apartments. In Los Angeles and Phoenix it runs the other way, because R5 is already their densest residential zone. Read what R5 zoning means for those cities, or R4 zoning for the step below.

Can you build a single family home on R6 land?

Often yes, but not everywhere. Nashville's R6 is built for single family homes and duplexes, and Louisville's R-6 allows single family homes alongside apartments.

Detroit is the exception in the table. Its R6 does not allow single family or two-family homes by right, only as conditional uses that need a separate approval.

Even where a house is allowed, building one on apartment-zoned land can leave value on the table. Lenders and appraisers often look at what the zoning allows, not just what sits on the lot today.

Can R6 zoning be changed?

Yes, through a rezoning or a zoning text change, both of which go through public hearings. Owners apply to the planning department, staff compare the request with the long-range plan, and the city council or county board decides.

Codes also change on their own. Raleigh's Missing Middle changes removed the six homes per acre cap from R-6 and let townhouses in by right. A lot's zoning name can stay the same while what it allows shifts.

Common misconceptions about R6 zoning

The most common mistake is reading New York's R6 rules into another city's code. Searches for R6 zoning often bring up New York material, which does not apply in Nashville, Raleigh or King County.

Another is assuming R6 always means apartments. In Nashville it is a one and two-family zone, and Raleigh's R-6 allows detached houses, attached houses and townhouses.

A third is thinking the number is a unit count per lot. R6 does not mean six homes on one lot. It might mean six homes per acre, a 6,000 square foot lot, or just the sixth zone on a list. If you are new to how these numbers work, the R1 zoning guide explains the basic ladder.

R6 zoning FAQ

What does R6 zoning mean?

R6 zoning means a residential district whose rules come from the local code. In New York City, Louisville and Detroit it is apartment zoning, in Nashville it allows houses and duplexes on 6,000 square foot lots, and in King County, Washington it means a base of six homes per acre.

Is R6 zoning high density?

Often it is medium to high density. Detroit calls R6 its High Density Residential District and Louisville allows up to 17.42 homes per acre, but Nashville and Raleigh use R-6 for houses, duplexes and townhouses.

Can you build a duplex on R6 zoning?

In many codes, yes. Nashville's R6 allows duplexes on lots that meet the minimum size and code conditions, and Louisville's R-6 allows two-family homes.

What is the difference between R5 and R6 zoning?

Where both exist, R6 allows more homes than R5. In Louisville, R-5 is single family at up to 7.26 homes per acre and R-6 is multi-family at up to 17.42. Some cities, like Los Angeles and Phoenix, have an R5 zone but no R6.

Other residential zoning codes

See the full guide to residential zoning, or search for your city's zoning map to check how a specific property is zoned.