What Does R5 Zoning Mean?

R5 zoning is a residential district, but what it allows depends heavily on the place. In Los Angeles and Phoenix it is apartment zoning, in Portland it is the "Residential 5,000" zone for houses and small multiplexes, and in some Washington counties it is a rural zone with about one home per five acres. The "R" stands for residential. The 5 is either the district's step on the local density ladder, a lot size, or a density number, depending on how the code is written.

"R5", "R-5" and "R 5" all mean the same district. Cities just write it differently on their zoning maps.

What does R5 zoning mean?

R5 zoning means a residential district that sits fifth in a city or county's list of residential zones, or a district named after a number five rule. In codes that count up from R1 single family, R5 is usually one of the highest density steps, where apartment buildings are the expected use.

That ladder is the most common pattern in residential zoning, but it is not the only one. Some codes use the number for something else:

  • A rank on the density ladder. Los Angeles and Phoenix both put R5 at the top of their multiple dwelling districts.
  • A minimum lot size. Portland's R5 is officially "Residential 5,000", named for a 5,000 square foot lot.
  • A density. In Fairfax County, Virginia, R-5 is the residential district at five dwelling units per acre.
  • Acres per home. Snohomish County and Clark County in Washington use R-5 for rural land with roughly one home per five acres.

So a listing that just says "zoned R-5" tells you very little until you know which city or county wrote the code.

What R5 zoning means in different cities

The same R5 label covers everything from high-rise apartments to five-acre rural lots. Each row below comes from that jurisdiction's own zoning code or planning department:

PlaceDistrict nameWhat it allows (short)
Los Angeles, CAR5 Multiple DwellingR4 uses plus clubs, lodges, hospitals and hotels. 200 sq ft of lot area per home, height set by the height district.
Phoenix, AZR-5 Multiple Family ResidenceAttached homes at 43.5 to 45.68 per acre, or 52.2 with a bonus.
New York City, NYR5 General Residence DistrictLower density district that allows all housing types, from houses to small apartment buildings, under a height cap.
Portland, ORR5 Residential 5,000Houses, ADUs, duplexes, triplexes, fourplexes and cottage clusters. Sites of 10,000 sq ft or more must hold at least two homes.
Fairfax County, VAR-5 Residential, Five Dwelling Units/AcreA mix of single family homes, detached and attached, at up to five homes per acre.
Snohomish County, WAR-5 Rural 5-AcreRural homes on lots of at least 200,000 sq ft (about 4.6 acres).
Clark County, WAR-5 Rural 5Rural homes on 5-acre lots, with farming and forestry encouraged alongside them.

The table shows three very different ideas behind the same code. Los Angeles and Phoenix use R5 as the top of a multi-family ladder. Los Angeles allows one home per 200 square feet of lot area, and the Los Angeles zoning code summary lists hotels and hospitals among its R5 uses.

New York, Portland and Fairfax County use R5 for lower density neighborhoods. Portland's R5 is still one of its single-dwelling zones, yet the Portland zoning code lets owners build up to a fourplex on a qualifying lot, with more units possible in some affordable projects.

The Washington counties sit at the far end. Their R-5 is rural land, closer in spirit to RR rural residential zoning than to anything in a city.

So what does R5 usually mean? In a city code that counts from R1 up, R5 most often means multi-family housing at a higher density than R4. In a county code, check whether the 5 is acres before assuming anything.

What can you build on R5 zoning?

On city R5 land you can usually build apartment buildings, and in most codes anything allowed in the lower residential zones too. In Los Angeles, for example, R5 allows everything R4 allows, and R4 in turn includes R3 uses such as apartment houses.

Where R5 is a multi-family zone, typical projects include:

  • Apartment buildings and condominiums
  • Townhouses and smaller multiplexes
  • Single family homes, though building one on high density land is often a poor use of the lot's value
  • Some institutional uses. Los Angeles adds clubs, lodges, hospitals and hotels in R5.

Investors looking at a multi-family property on R5 land should check three numbers first: homes per acre or lot area per home, floor area ratio, and parking. The FAR calculator shows how much building floor area a lot can hold, and the parking calculator shows how many spaces a project may need.

In Portland's R5 the answer is smaller buildings: a house, a house with ADUs, or a duplex up to a fourplex. In rural R-5 counties the answer is usually one home on a large lot, with room for gardens, animals and outbuildings.

What is the difference between R4 and R5 zoning?

Where both districts exist, R5 usually allows more homes on the same land than R4, and sometimes a few extra non-residential uses. The gap can be large:

PlaceR4R5
Los Angeles, CA400 sq ft of lot area per home (about 12 homes on a 5,000 sq ft lot)200 sq ft of lot area per home (about 25 homes on a 5,000 sq ft lot)
Phoenix, AZAttached homes at 29 to 30.45 per acreAttached homes at 43.5 to 45.68 per acre
New York City, NYLower density general residence districtLower density general residence district with more building bulk than R4
Extra usesLos Angeles adds churches, schools and childcare over R3Los Angeles adds clubs, lodges, hospitals and hotels over R4

If you are comparing a lot with its neighbors, read what R4 zoning means and what R6 zoning allows. In New York the next step up, R6, is where taller apartment buildings start. Phoenix and Los Angeles have no R6 at all, so R5 is the top of their residential ladder.

What is the minimum lot size in R5 zoning?

There is no single R5 minimum lot size. It ranges from a few thousand square feet in a city to almost five acres in a rural county.

  • Portland R5: the zone is named for a 5,000 square foot lot, and sites of 10,000 square feet or more must have at least two homes.
  • Snohomish County R-5: 200,000 square feet, which the county treats as its "five acres" for land division.
  • Clark County R-5: 5 acres, with cluster lots as small as 1 acre when the rest of the land stays as a remainder parcel.
  • Los Angeles R5: the rule that matters most is lot area per home, 200 square feet, rather than a large minimum lot.

The setbacks, height limit and lot coverage cap then decide how much of that lot you can actually build on.

What do R5A, R5B and R5D mean?

R5A, R5B and R5D are New York City versions of R5 with their own building shape rules. The city's Zoning Resolution names them the R5A Detached Residence District and the R5B and R5D General Residence Districts.

R5A is the most limited. Outside of certain qualifying sites, it is for single or two-family detached houses. R5B and R5D are general residence districts, so they allow a broader range of housing types. Searches for "R5B zoning" almost always refer to New York.

Can R5 zoning be changed?

Yes. A rezoning can move a lot into or out of R5, but nothing about it is automatic. Expect an application fee, a staff report that tests the request against the long-range plan, mailed notice to neighbors, and a vote by the council or county board after public hearings.

Rezonings to R-5 happen in rural counties too, and the stakes are easy to see. Clark County, Washington sets a 20 acre minimum lot in R-20 and a 5 acre minimum in R-5, so moving a 50 acre parcel from R-20 to R-5 takes it from room for 2 lots to room for about 10.

Before you plan around a rezoning, find the property on the zoning map and confirm the current district and any overlays.

Common misconceptions about R5 zoning

The biggest misconception is that R5 means the same thing everywhere. It does not. An R5 lot in Los Angeles and an R-5 parcel in Snohomish County have almost nothing in common.

Another is that R5 always means apartments. In New York, Portland and Fairfax County it is a lower density zone, and in rural Washington it is mostly single homes on acreage.

A third is that a higher number means you can build anything you want. Even a high density R5 lot still has height, setback, parking and open space rules, and those often limit a project more than the unit count does.

R5 zoning FAQ

What does R5 zoning mean?

R5 zoning means a residential district whose rules depend on the local code. In Los Angeles and Phoenix it is high density apartment zoning, in Portland it allows houses up to fourplexes, and in some Washington counties it means rural land with about one home per five acres.

Is R-5 the same as R5?

Yes. R5, R-5 and R 5 are the same district written in different styles. What matters is which city or county's code the property falls under.

Can you build apartments on R5 zoning?

Usually yes in cities that use R5 as a multi-family district, such as Los Angeles and Phoenix. In Portland R5 allows up to a fourplex on a qualifying lot, and in rural R-5 counties apartments are generally not the intended use.

How many homes per acre does R5 zoning allow?

It depends on the place. Phoenix R-5 allows 43.5 to 45.68 attached homes per acre before bonuses, Fairfax County R-5 allows five per acre, and rural R-5 zones allow about one home per five acres.

Other residential zoning codes

See the full guide to residential zoning, or search for your city's zoning map to check how a specific property is zoned.