R4 zoning usually means a residential district one step denser than R3. In cities with a classic R-1 to R-5 ladder that means apartment buildings, but many counties use R-4 for single family homes at about four per acre. The "R" stands for residential, and the "4" is either the fourth step on the ladder or a count of homes per acre.
No residential code swings as widely as R4. The same four characters can describe an apartment building in Los Angeles and a quiet cul-de-sac of houses in suburban Virginia. That is why it pays to read the local definition before you price a lot or plan a project.
R-4, R4 and R 4 are one district written three ways. Suffixes like R4-1, R-4A or R4B point to a sub-district with its own rules.
R4 zoning means a residential district whose meaning comes from how the local code numbers its zones. Two systems account for almost every R-4 you will see.
In a step ladder, the number is a rank. R-1 is the lowest density, and each step up allows more housing on the same land. Here R-4 sits above the R-3 medium density zone, so it usually allows larger multi-family buildings.
In a density count, the number is the homes allowed per acre. R-4 means roughly four homes per acre, which is a single family subdivision with lots of around a quarter acre. Fairfax County, Virginia and King County, Washington both work this way.
The residential zoning overview shows how both ladders line up with low, medium and high density housing.
R4 means apartments in some places and houses in others. Each row below comes from that city's or county's own zoning code or official planning page:
| Place | District name | What it allows |
|---|---|---|
| Los Angeles, CA | R4 Multiple Dwelling | R3 uses plus churches, schools, child care and homeless shelters; 400 sq ft of lot area per unit |
| Phoenix, AZ | R-4 Multiple Family Residence | Attached homes at 29 to 30.45 per acre (34.8 with bonus) |
| New York City, NY | R4 General Residence District | All housing types, at a slightly higher density than R3-2 |
| New York City, NY | R4-1 Detached and Semi-Detached Residence District | One- and two-family houses, detached or semi-detached, on most lots |
| King County, WA | R-4 Urban Residential | Base density of four homes per acre; detached houses, duplexes, houseplexes and townhouses |
| Raleigh, NC | R-4 | A detached house or tiny house, or a two-unit attached house, 10,000 sq ft minimum lot |
| Fairfax County, VA | R-4 Residential, Four Dwelling Units/Acre | Single family detached homes at four units per acre |
| Atlanta, GA | R-4 Single-Family Residential | One house per lot, 9,000 sq ft minimum lot, 70 ft frontage |
The table splits right down the middle. Los Angeles and Phoenix use R4 for apartment buildings, and New York's R4 allows every housing type. King County, Raleigh, Fairfax County and Atlanta use R-4 for houses, with at most a duplex or a small multiplex.
The density gap is huge. Phoenix R-4 allows about 30 attached homes per acre. King County and Fairfax County allow about four. Those are the same code letters with a sevenfold difference in housing.
So R4 "usually" means high or medium-high density apartments only in cities that rank their zones on a ladder. In the many counties that name zones by units per acre, R-4 is a single family district. The Phoenix district list is a clear example of the ladder version.
It depends on which kind of R-4 you have. In a ladder city, you can usually build anything from a house up to a mid-size multi-family property. In a density county, you can usually build houses and, increasingly, a duplex.
In apartment-style R4 districts, common uses include:
In house-style R-4 districts, the list is shorter: a detached home, an accessory dwelling unit where allowed, garages and sheds, and in some places a duplex or two-unit attached house.
For apartment projects, the building's size is often set by floor area ratio as much as by unit count. The FAR calculator shows how much floor area a lot can carry.
R4-1 is a sub-district of R4. In New York City, R4-1 permits one- and two-family houses, detached or semi-detached, on most lots, even though plain R4 allows all housing types.
That meaning comes from New York's own district list. Other cities use "-1" for a height limit or a lot size class instead, so read your own code before relying on the suffix.
R4 allows more homes on the same land than R3. In most codes the housing types overlap, and the change is in density.
| R3 zoning | R4 zoning | |
|---|---|---|
| Usual density label | Medium | Medium to high |
| Los Angeles lot area per unit | 800 sq ft | 400 sq ft |
| Phoenix attached homes per acre | 14.5 to 15.23 | 29 to 30.45 |
| Fairfax County homes per acre | 3 | 4 |
| Atlanta minimum lot | 18,000 sq ft | 9,000 sq ft |
On a 10,000 square foot Los Angeles lot, the lot area math alone allows about 12 units in R3 and about 25 in R4. Parking, height and open space rules usually bring both numbers down. For the medium density step, see the guide to R3 zoning.
R5 is the next step up in density, and in some codes it also adds non-housing uses. The building types are similar, but R5 allows more units or larger buildings.
| R4 zoning | R5 zoning | |
|---|---|---|
| Phoenix attached homes per acre | 29 to 30.45 | 43.5 to 45.68 |
| Los Angeles added uses | Churches, schools, child care, shelters | R4 uses plus clubs, lodges, hospitals and hotels |
| Typical building | Low to mid-rise apartments | Larger apartment buildings |
If you are weighing an R4 site against an R5 one, compare the actual unit counts and allowed uses rather than the labels. The details are in our guide to R5 zoning.
Yes, by rezoning, which means an application, a staff review, public notice and hearings. The planning commission recommends, and the city council or county board makes the final call.
In a density county, owners sometimes ask to go from R-4 to R-6 or R-8 to fit more lots in a subdivision. In a ladder city, the usual request is R4 to a commercial or mixed-use zone along a main road.
New housing rules are also changing what R-4 allows without any rezoning. King County's 2024 plan update, for instance, added duplexes, houseplexes and townhouses to its R-4 zone. Check the current code rather than an old listing.
The first is that R4 means four units per lot. In King County and Fairfax County the "4" is per acre, and in Los Angeles it has nothing to do with a unit count at all.
The second is that R4 is always apartments. Four of the seven places in the table above use R-4 mainly for houses.
The third is that a higher number always means a bigger lot. In Atlanta the opposite is true: R-4 lots are half the size of R-3 lots, because the districts get denser as the number rises.
Last, a buyer may assume an existing fourplex on an R-4 lot is legal. If the zone only allows houses, that building could be nonconforming. Confirm it with the planning office, and look the parcel up on the zoning map first.
R4 residential zoning is a housing district that is either a medium to high density apartment zone or a single family zone at about four homes per acre. Which one depends on how the local code numbers its districts.
In King County, Washington, R-4 is an urban residential zone with a base density of four homes per acre. Since the 2024 plan update it allows duplexes, houseplexes and townhouses as well as detached homes.
In cities like Los Angeles and Phoenix, yes, R4 is an apartment zone. In places like Fairfax County, Raleigh and Atlanta, R-4 is for houses and does not allow apartment buildings.
Yes, in nearly every code that has both. Phoenix R-4 allows about twice as many attached homes per acre as R-3, and Los Angeles R4 needs half as much lot area per unit as R3.
See the full guide to residential zoning, or search for your city's zoning map to check how a specific property is zoned.